LORD® 204 Acrylic Adhesive Where To Buy
Product Information
LORD® 204 acrylic adhesive when cured with LORD Accelerator 4, 17 or 19 creates an adhesive system that will bond a wide variety of prepared or unprepared metals and plastics. LORD 204 acrylic adhesive in combination with the recommended accelerator replaces welding, brazing, riveting and other mechanical fastening methods.
LORD 204 acrylic adhesive can be cured with either LORD Accelerator 4, LORD Accelerator 17 or LORD Accelerator 19. LORD Accelerator 4 is a no-mix accelerator applied to the substrate before the acrylic adhesive. LORD Accelerators 17 and 19 must be mixed into the acrylic adhesive prior to application. LORD Accelerator 19 is available in off-white or black.
Shelf Life
Shelf life is six months when stored below 80°F (27°C) in original, unopened container. Storage temperatures of 40-50°F (4-10°C) are recommended. If stored cold, allow product to return to room temperature before using.
Features and Benefits
Bonds Unprepared Metals - requires little or no substrate preparation.
Versatile - bonds a wide variety of substrates such as metals, ceramics and plastics; insensitive to minor deviations from correct mix ratio.
Non-Sag - remains in position when applied on vertical or overhead surfaces, allowing for greater process flexibility.
Temperature Resistant - performs at temperatures from -40°F to +300°F (-40°C to +149°C).
Environmentally Resistant - resists dilute acids, alkalis, solvents, greases, oils and moisture; provides excellent resistance to indirect UV exposure, salt spray and weathering.
Typical Properties*
| Appearance | Off-white Paste |
|
Viscosity, cP @ 77°F (25°C) Brookfield HAT Spindle 7, 20 rpm |
100,000-300,000 |
| Density, lb/gal (kg/m3) | 8.7-9.3 (1042-1114) |
|
Flash Point, °F (°C) Closed Cup |
66 (19) |
| Work Time, min @ 75°F (24°C) | 6-8 |
| Time to Handling Strength, min @ 70°F (21°C) | 20-30 |
| Cure Time**, hr | 24 |
| Mixed Appearance | Color dependent on accelerator used |
| Mixed Solids Content by Weight, % | 100 |
*Data is typical and not to be used for specification purposes.
**Reaches 90% of ultimate strength after 2 hours.
Guns and Accessories
| LORD-Pak™ 50 Manual Dispensing Gun | |
 |
handheld, manual dispensing system for small jobs
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4” bead = 4.5 ft per 50 mL cartridge. |
| LORD-Pak™ 50 Replacement 1:1 and 2:1 Plunger | |
|
1:1 and 2:1 plunger for use on LORD-Pack 50 manual dispensing gun |
| LORD-Pak™ 200 Manual Dispensing Gun | |
larger handheld, manual dispensing system for field repairs
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 19 ft per 200 mL cartridge. |
|
| LORD-Pak™ 200 Pneumatic Dispensing Gun | |
larger handheld, pneumatic dispensing system for production applications
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 19 ft per 200 mL cartridge. |
|
| Mixing Tip 0.25 x 6 x 21 elm. (package of 12) | |
|
0.25 x 6 x 21 element, package of 12 - For use with 50 mL |
| Mixing Tip 0.25 x 6 x 21 elm. (package of 144) | |
| 0.25 x 6 x 21 element, package of 144 | |
| Mixing Tip 0.375 x 9 x 24 elm. (package of 12) | |
|
0.375 x 9 x 24 element, package of 12 - For use with CX |
| Mixing Tip 0.375 x 11 x 24 elm. (package of 12) | |
| 0.375 x 11 x 24 element, package of 12 | |
Auxiliary Products
| LORD<sup>®</sup> 459T Adhesion Enhancer/Surface Modifier |
|
single-component primer in toluene solvent, for direct application; for promoting adhesion of thermoplastic elastomers (TPEs), polyolefins (TPOs) and EPDM Features and BenefitsVersatile - enhances adhesion to diffi cult-to-bond elastomers, increasing the adhesion of coatings, double-sided tape and adhesives. Easy to Apply - low viscosity allows for easy application; no mixing required. Convenient - requires very low dry film weights to enhance adhesion to coatings and double-sided tapes. |
| LORD<sup>®</sup> 459X Adhesion Enhancer/Surface Modifier |
|
single-component primer in xylene solvent, diluted for direct application; for promoting adhesion of thermoplastic elastomers (TPEs), Polyolefins (TPOs) and EPDM; meets California's VOC requirements Features and BenefitsVersatile - enhances adhesion to difficult-to-bond elastomers, increasing the adhesion of coatings, double-sided tape and adhesives. Easy to Apply - low viscosity allows for easy application; no dilution necessary. Convenient - requires very low dry film weights to enhance adhesion to coatings and double-sided tapes. |
| LORD<sup>®</sup> 7701 Adhesion Enhancer/Surface Modifier |
|
single-component, solvent-based surface treatment for various vulcanized, thermoplastic polymeric materials Features and BenefitsVersatile – functions as a cleaner and surface conditioner; treats a wide variety of elastomer functional materials. Easy to Apply – applies easily by wipe, brush, dip or flood methods. Convenient – requires no mixing. Improved Adhesion – improves adhesion to cast urethanes and cured rubber. Fast Drying – adhesion enhancer/surface modifier flashes off within five minutes or less. Environmentally Resistant – promotes increased environmental resistance by allowing the treated surface to be more easily wet. |
| LORD<sup>®</sup> 7713 Adhesion Enhancer/Surface Modifier |
|
single-component, room temperature curing primer; for adhesive bonding of glass reinforced polyester substrates Features and BenefitsVersatile - enhances adhesion to a variety of substrates when utilized prior to most adhesive applications. Easy to Apply - low viscosity allows for easy application; no dilution necessary. |
| LORD<sup>®</sup> Accelerator 4 |
|
no-mix accelerator; use with bond thickness of 20 mils or less Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Extended Work Time – provides extended assembly time as adhesive does not begin cure until it comes in contact with surface coated with dry accelerator. Easy to Apply – applies easily by brush, wipe, spray or dip methods onto one or both bonding surfaces. Fast Cure – dries in approximately one minute to an off-white crystalline film. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 17 |
|
mix-in accelerator; 10:1 mix ratio Features and BenefitsConvenient - provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly - contains no solvent, non-flammable and virtually odorless. Environmentally Resistant - resists common environmental conditions when used with LORD acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 19 |
|
mix-in accelerator; 2:1 or 4:1 mix ratio Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly – contains no solvent, non-flammable and virtually odorless. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. Temperature Resistant – improves high temperature resistance of LORD 200, 400 and 500 series acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 26 |
|
no-mix accelerator; use with bond thicknesses of 20 mils or less; no chlorinated solvents Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Extended Work Time – provides extended assembly time as adhesive does not begin cure until it comes in contact with surface coated with dry accelerator. Easy to Apply – applies easily by brush, wipe, spray or dip methods onto one or both bonding surfaces. Fast Cure – dries in approximately 15 minutes to an off-white crystalline film. Environmentally Friendly – does not contain chlorinated solvents. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. |
| LORD<sup>®</sup> AP-134 Adhesion Enhancer/Surface Modifier |
|
single-component, low viscosity, reactive polymer primer; for glass and ceramics Features and BenefitsVersatile - provides a wide range of product applications by functioning as a primer to a variety of polar substrates and as an adhesive for reaction injection molding (RIM) of polyurethane to glass. Easy to Apply - applies easily by spray, dip or polyester felt applicator. Convenient - requires only a single coat for most applications, reducing labor, solvent usage, inventory and shipping costs. |
Literature
| Download | Type | Name | |
|---|---|---|---|
 |
Selector Guide | LORD Structural Adhesives Selector Guide | |
|
|
Technical Data Sheet | LORD 204 Acrylic Adhesive | |
|
|
Application Guide | Structural Adhesive Bonding Application Guide | |
|
|
Safety Data Sheet | LORD 204 |
Related Blog Posts