LORD® 606 Acrylic Adhesive with LORD Accelerator 6 or 6GB Where To Buy
Product Information
LORD® 606 acrylic adhesive when cured with LORD Accelerator 6 or 6GB creates a fast-setting adhesive system that will bond composites including DCPD (dicyclopentadiene) resin and modified DCPD resin based FRP (fiber reinforced plastic). This mixed adhesive can also cross-bond composites to many metals.
LORD 606 adhesive in combination with LORD Accelerator 6 or 6GB utilize a unique patented technology to create exceptionally strong bonds with excellent surface cure and minimal surface preparation.
LORD 606 adhesive can be mixed with either LORD Accelerator 6 or LORD Accelerator 6GB. LORD Accelerator 6GB allows precise control of the adhesive bondline thickness due to its content of glass beads.
Shelf Life
Shelf life is six months when stored below 80°F (27°C) in original, unopened container. Storage temperatures of 40-50°F (4-10°C) are recommended. If stored cold, allow product to return to room temperature before using. Protect from exposure to direct sunlight.
LORD 606 adhesive is flammable. Do not store or use near heat, sparks or open flame.
Features and Benefits
Versatile – bonds difficult-to-bond composites, such as DCPD based FRP, and a wide range of metals with minimal surface preparation.
Environmentally Resistant – resists dilute acids, alkalis, solvents, water immersion, moisture and weathering.
Gap Filling Capability – fills gaps as large as 0.5-1.0 inch (12.7-25.4 mm).
Non-Sag – remains in position when applied on vertical or overhead surfaces, allowing for greater process flexibility.
Typical Properties*
| Appearance | White to Off-white Paste |
| Viscosity, cP | 100,000-300,000 |
| Density, lb/gal (kg/m3) | 8.7-9.7 (1042-1162) |
| Flash Point, °F (°C) | 59 (15) |
| Work Time, min @ 75°F (24°C) | 4-6 |
| Time to Handling Strength, min @ 75°F (24°C) | 20-24 |
| Cure Time, hr | 24 |
| Mixed Appearance | Grey Paste |
| Mixed Solids Content by Weight, % | 100 |
*Data is typical and not to be used for specification purposes.
Guns and Accessories
| LORD-Pak™ 400 or 485 mL Cartridge Manual Dispensing Gun | |
larger handheld, manual dispensing system for field repairs
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 46 ft per 485 mL cartridge. |
|
| LORD-Pak™ 400 or 485 mL Cartridge Pneumatic Dispensing Gun | |
larger handheld, pneumatic dispensing system for production applications
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 46 ft per 485 mL cartridge. |
|
| Mixing Tip 0.375 x 10 x 24 elm. (package of 12) | |
| 0.375 x 10 x 24 element, package of 12 | |
Auxiliary Products
| LORD<sup>®</sup> 7713 Adhesion Enhancer/Surface Modifier |
|
single-component, room temperature curing primer; for adhesive bonding of glass reinforced polyester substrates Features and BenefitsVersatile - enhances adhesion to a variety of substrates when utilized prior to most adhesive applications. Easy to Apply - low viscosity allows for easy application; no dilution necessary. |
| LORD<sup>®</sup> Accelerator 4 |
|
no-mix accelerator; use with bond thickness of 20 mils or less Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Extended Work Time – provides extended assembly time as adhesive does not begin cure until it comes in contact with surface coated with dry accelerator. Easy to Apply – applies easily by brush, wipe, spray or dip methods onto one or both bonding surfaces. Fast Cure – dries in approximately one minute to an off-white crystalline film. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 6 |
|
mix-in accelerator; 10:1 mix ratio Features and BenefitsConvenient - provides room temperature cure with all LORD 600 series acrylic adhesives. Environmentally Recommended - contains no solvent, non-flammable and virtually odorless. Environmentally Resistant - resists common environmental conditions when used with LORD acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 6GB |
|
Mix-in accelerator; 10:1 mix ratio; GB version offers bondline control Features and BenefitsConvenient - provides room temperature cure with all LORD 600 series acrylic adhesives. Environmentally Recommended - contains no solvent, non-flammable and virtually odorless. Environmentally Resistant - resists common environmental conditions when used with LORD acrylic adhesives. |
| LORD<sup>®</sup> AP-134 Adhesion Enhancer/Surface Modifier |
|
single-component, low viscosity, reactive polymer primer; for glass and ceramics Features and BenefitsVersatile - provides a wide range of product applications by functioning as a primer to a variety of polar substrates and as an adhesive for reaction injection molding (RIM) of polyurethane to glass. Easy to Apply - applies easily by spray, dip or polyester felt applicator. Convenient - requires only a single coat for most applications, reducing labor, solvent usage, inventory and shipping costs. |
Literature
| Download | Type | Name | |
|---|---|---|---|
 |
MSDS (US) | LORD 606 | |
|
|
Selector Guide | LORD Structural Adhesives Selector Guide | |
|
|
Technical Data Sheet | LORD 606 Adhesive with LORD Accelerator 6 or 6GB | |
|
|
Application Guide | Structural Adhesive Bonding Application Guide |
Related Blog Posts
