LORD® 406 Acrylic Adhesive Where To Buy
Product Information
LORD® 406 acrylic adhesive in combination with LORD Accelerator 17, 19 or 19GB can be used to replace welding, brazing, riveting and other mechanical fastening methods. The 406/19 and 406/19GB adhesive systems perform particularly well in low-temperature environments and applications that are subject to high impact or high peel loads.
LORD 406 acrylic adhesive, when mixed with LORD Accelerator 17, 19 or 19GB, creates an adhesive system that bonds a wide variety of prepared or unprepared metals and engineered plastics. The 406-19 and 406-19GB adhesive systems are specifically formulated to provide the highest impact and peel strengths available in a room temperature curing adhesive.
LORD 406 acrylic adhesive can be mixed with either LORD Accelerator 17, LORD Accelerator 19 or LORD Accelerator 19GB. LORD Accelerator 19 improves the high temperature resistance of LORD 406 acrylic adhesive, and is available in off-white or black. LORD Accelerator 19GB allows precise control of the adhesive bondline thickness due to its content of glass beads. LORD Accelerator 19GB is available in off-white, red or grey.
Shelf Life
Typical shelf life is nine months when stored below 80°F (27°C) in original, unopened container. Storage temperatures of 40-50°F (4-10°C) are recommended. If stored cold, allow product to return to room temperature before using. Protect from exposure to direct sunlight.
LORD 406 acrylic adhesive is flammable. Do not store or use near heat, sparks or open flame.
Features and Benefits
Versatile – bonds a wide range of unprepared metals with minimal substrate preparation, as well as engineered thermoplastics including XENOY®, polycarbonate, ABS and acrylics.
Temperature Resistant – performs at temperatures from -40°F to +300°F (-40°C to +149°C).
Note: Based on test results, LORD 406/19GB adhesive system exhibits post bake/powder coating temperature resistance up to 400°F (204°C) for 90 minutes. Customer specific substrates should always be evaluated for specific application performance.
Environmentally Resistant – resists dilute acids, alkalis, solvents, greases, oils, moisture, salt spray and weathering; provides excellent resistance to indirect UV exposure.
Non-Sag – remains in position when applied on vertical or overhead surfaces, allowing for greater process flexibility.
UL Approved Adhesive – when mixed with LORD Accelerator 19, adhesive system is UL 746C certified.
XENOY is a trademark of General Electric Company.
Typical Properties*
| Appearance | Off-white to Tan Paste |
|
Viscosity, cP @ 77°F (25°C) Brookfield |
100,000 - 300,000 |
| Density, lb/gal (kg/m3) | 9.10 - 9.70 (1090 - 1162) |
|
Flash Point, °F (°C) Closed Cup |
59 (15) |
| Working Time, min @ 75°F (24°C) | 6 - 10 |
|
Time to Handling Strength, min @ 75°F (24°C) 50 psi Shear |
12 - 17 |
| Full Cure Time, hr @ 75°F (24°C) | 24 |
| Mixed Appearance | Color dependent on accelerator used |
| Mixed Solids Content by Weight, % | 100 |
*Data is typical and not to be used for specification purposes.
Guns and Accessories
| Mixing Tip 0.25 x 7.5 x 24 elm. (package of 12) | |
 |
0.25 x 7.5 x 24 element, package of 12 |
| Mixing Tip 0.375 x 9.5 x 24 elm. (package of 12) | |
|
0.375 x 9.5 x 24 element, package of 12 |
| Mixing Tip 0.375 x 9 x 24 elm. (package of 12) | |
|
0.375 x 9 x 24 element, package of 12 - For use with CX |
| Mixing Tip 0.25 x 6 x 21 elm. (package of 12) | |
|
0.25 x 6 x 21 element, package of 12 - For use with 50 mL |
| Mixing Tip 0.25 x 6 x 21 elm. (package of 144) | |
| 0.25 x 6 x 21 element, package of 144 | |
| LORD-Pak™ 375 mL Cartridge Manual Dispensing Gun | |
|
side-by-side, snap-together cartridge systems for manual dispensing |
| LORD-Pak™ 375 mL Cartridge Pneumatic Dispensing Gun | |
| side-by-side, snap-together cartridge systems for pnuematic dispensing | |
| LORD-Pak™ CX Manual Dispensing Gun (Configured for 10:1) | |
manual dispensing system utilizing a coaxial cartridge containing two adhesive parts
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 38.5 ft per 380 mL cartridge. |
|
| LORD-Pak™ CX Manual Dispensing Gun (Configured for 4:1) | |
|
manual dispensing system utilizing a coaxial cartridge containing two adhesive parts
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 38.5 ft per 380 mL cartridge. |
| LORD-Pak™ CX Pneumatic Dispensing Gun | |
pneumatic dispensing system utilizing a coaxial cartridge containing two adhesive parts
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 38.5 ft per 380 mL cartridge. |
|
| LORD-Pak™ 200 Manual Dispensing Gun | |
larger handheld, manual dispensing system for field repairs
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 19 ft per 200 mL cartridge. |
|
| LORD-Pak™ 200 Pneumatic Dispensing Gun | |
larger handheld, pneumatic dispensing system for production applications
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 19 ft per 200 mL cartridge. |
|
| LORD-Pak™ 50 4:1 Plunger | |
|
4:1 plunger for use on LORD-Pack 50 manual dispensing gun |
| LORD-Pak™ 50 Manual Dispensing Gun | |
|
handheld, manual dispensing system for small jobs
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4” bead = 4.5 ft per 50 mL cartridge. |
Auxiliary Products
| LORD<sup>®</sup> 7713 Adhesion Enhancer/Surface Modifier |
|
single-component, room temperature curing primer; for adhesive bonding of glass reinforced polyester substrates Features and BenefitsVersatile - enhances adhesion to a variety of substrates when utilized prior to most adhesive applications. Easy to Apply - low viscosity allows for easy application; no dilution necessary. |
| LORD<sup>®</sup> Accelerator 17 |
|
mix-in accelerator; 10:1 mix ratio Features and BenefitsConvenient - provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly - contains no solvent, non-flammable and virtually odorless. Environmentally Resistant - resists common environmental conditions when used with LORD acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 19 |
|
mix-in accelerator; 2:1 or 4:1 mix ratio Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly – contains no solvent, non-flammable and virtually odorless. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. Temperature Resistant – improves high temperature resistance of LORD 200, 400 and 500 series acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 19 Black |
|
mix-in accelerator; 2:1 or 4:1 mix ratio Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly – contains no solvent, non-flammable and virtually odorless. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. Temperature Resistant – improves high temperature resistance of LORD 200, 400 and 500 series acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 19GB |
|
mix-in accelerator; 2:1 or 4:1 mix ratio Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly – contains no solvent, non-flammable and virtually odorless. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. Temperature Resistant – improves high temperature resistance of LORD 200, 400 and 500 series acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 19GB Grey |
|
mix-in accelerator; 2:1 or 4:1 mix ratio Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly – contains no solvent, non-flammable and virtually odorless. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. Temperature Resistant – improves high temperature resistance of LORD 200, 400 and 500 series acrylic adhesives. |
| LORD<sup>®</sup> Accelerator 19GB Red |
|
mix-in accelerator; 2:1 or 4:1 mix ratio Features and BenefitsConvenient – provides room temperature cure with all LORD acrylic adhesives. Environmentally Friendly – contains no solvent, non-flammable and virtually odorless. Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives. Temperature Resistant – improves high temperature resistance of LORD 200, 400 and 500 series acrylic adhesives. |
| LORD<sup>®</sup> AP-134 Adhesion Enhancer/Surface Modifier |
|
single-component, low viscosity, reactive polymer primer; for glass and ceramics Features and BenefitsVersatile - provides a wide range of product applications by functioning as a primer to a variety of polar substrates and as an adhesive for reaction injection molding (RIM) of polyurethane to glass. Easy to Apply - applies easily by spray, dip or polyester felt applicator. Convenient - requires only a single coat for most applications, reducing labor, solvent usage, inventory and shipping costs. |
Literature
| Download | Type | Name | |
|---|---|---|---|
 |
MSDS (US) | LORD 406 | |
|
|
Selector Guide | LORD Structural Adhesives Selector Guide | |
|
|
Technical Data Sheet | LORD 403, 406 and 410 Acrylic Adhesives with LORD Accelerator 17, 19 or 19GB | |
|
|
Technical Service Bulletins | Volatility of LORD 400 Series | |
|
|
Powder Coating after Bonding with LORD 400 Series Acrylic Adhesives | ||
|
|
Powder Coating after Bonding with LORD Acrylic Adhesives | ||
|
|
Troubleshooting Guide | LORD 400 Series Acrylic Adhesives Troubleshooting Guide | |
|
|
Application Guide | Structural Adhesive Bonding Application Guide |
Related Blog Posts