LORD Maxlok™ MX/T6 Acrylic Adhesive Where To Buy
Product Information
LORD Maxlok™ MX/T6 acrylic adhesive replaces welding, brazing, riveting and other mechanical fastening methods especially over a wide range of temperature environments subject to high impact or high peel loads.
Shelf Life
Shelf life of each component is nine months when stored at temperatures under 80°F (27°C) in original, unopened container. For maximum shelf life, storage temperatures of 40-50°F (4-10°C) are recommended. If stored at these cooler temperatures, allow product to return to room temperature before using. Protect from exposure to direct sunlight.
LORD Maxlok MX/T6 acrylic adhesive is flammable. Do not store or use near heat, sparks or open flame.
Features and Benefits
Versatile – bonds a wide range of unprepared metals with minimal substrate preparation.
Temperature Resistant – performs at temperatures from -40°Fto +300°F (-40°C to +149°C).
Note: Based on test results, LORD Maxlok MX/T6 adhesive system exhibits post bake/powder coating temperature resistance up to 400°F (204°C) for 90 minutes. Customer specific substrates should always be evaluated for specific application performance.
Environmentally Resistant – resists dilute acids, alkalis, solvents, greases, oils, moisture, salt spray and weathering; provides excellent resistance to indirect UV exposure.
UL Approved Adhesive - Maxlok MX/T6 adhesive system is UL 746C certified.
Precise Bondline – allows precise control of adhesive bondline thickness due to its content of glass beads, 0.01" (0.025 cm) diameter.
Non-Sag – remains in position when applied on vertical or overhead surfaces, allowing for greater process flexibility.
Typical Properties*
| Mixed Appearance | Grey Paste |
| Mixed Solids Content by Weight, % | 100 |
| Working Time, min @ 77°F (25°C) | 6 - 9 |
|
Time to Handling Strength, min @ 77°F (25°C) 50 psi Shear |
20 - 24 |
| Cure Time, hr | 24 |
*Data is typical and not to be used for specification purposes.
Guns and Accessories
| Mixing Tip 0.34" x 5.8" x 24 elm. (package of 12) | |
| 0.34" x 5.8" x 24 element, package of 12 | |
| Mixing Tip 0.34" x 5.8" x 24 elm. (package of 144) | |
| 0.34" x 5.8" x 24 element, package of 144 | |
| Mixing Tip 0.25 x 6 x 21 elm. (package of 12) | |
 |
0.25 x 6 x 21 element, package of 12 - For use with 50 mL |
| Mixing Tip 0.25 x 6 x 21 elm. (package of 144) | |
| 0.25 x 6 x 21 element, package of 144 | |
| LORD-Pak™ 375 mL Cartridge Manual Dispensing Gun | |
|
side-by-side, snap-together cartridge systems for manual dispensing |
| LORD-Pak™ 375 mL Cartridge Pneumatic Dispensing Gun | |
| side-by-side, snap-together cartridge systems for pnuematic dispensing | |
| LORD-Pak™ 50 4:1 Plunger | |
|
4:1 plunger for use on LORD-Pack 50 manual dispensing gun |
| LORD-Pak™ 50 Manual Dispensing Gun | |
|
handheld, manual dispensing system for small jobs
Features and Benefits• Approximate linear coverage of mixed adhesive, dispensed as 1/4” bead = 4.5 ft per 50 mL cartridge. |
Auxiliary Products
| LORD<sup>®</sup> 7713 Adhesion Enhancer/Surface Modifier |
|
single-component, room temperature curing primer; for adhesive bonding of glass reinforced polyester substrates Features and BenefitsVersatile - enhances adhesion to a variety of substrates when utilized prior to most adhesive applications. Easy to Apply - low viscosity allows for easy application; no dilution necessary. |
| LORD<sup>®</sup> AP-134 Adhesion Enhancer/Surface Modifier |
|
single-component, low viscosity, reactive polymer primer; for glass and ceramics Features and BenefitsVersatile - provides a wide range of product applications by functioning as a primer to a variety of polar substrates and as an adhesive for reaction injection molding (RIM) of polyurethane to glass. Easy to Apply - applies easily by spray, dip or polyester felt applicator. Convenient - requires only a single coat for most applications, reducing labor, solvent usage, inventory and shipping costs. |
Literature
| Download | Type | Name | |
|---|---|---|---|
| Safety Data Sheet | LORD MAXLOK T6 | |
|
| Safety Data Sheet | LORD MAXLOK MX | |
|
|
Selector Guide | LORD Structural Adhesives Selector Guide | |
|
|
Technical Data Sheet | Maxlok MX/T3, MX/T6 and MX/T18 Acrylic Adhesives | |
|
|
Application Guide | Structural Adhesive Bonding Application Guide | |
|
|
Powder Coating after Bonding with LORD Acrylic Adhesives |
Related Blog Posts